TECAPEI natural Sabic Ultem 1000 series - Stock Shapes rods plates tubes Chemical Designation PEI Polyetherimide Main features high dielectric strength inherent flame retardant low smoke emissions easily machinable to tight tolerance high thermal and mechanical capacity flame retardant according to UL94 V-0 Colour amber transparent transparent Density 1.27 gcm3 Target Industries aircraft and aerospace technology automotive industry electronics medical technology semiconductor technology food engineering food processing Mechanical properties condition value Modulus of elasticity tensile test 73 F 430000 psi ASTM D 638 Tensile strength at break 73 F 17500 psi ASTM D 638 Elongation at yield tensile test 73 F 7 ASTM D 638 Elongation at break tensile test 73 F 40 ASTM D 638 Flexural strength 73 F 23000 psi ASTM D 790 Modulus of elasticity flexural test 73 F 480000 psi ASTM D 790 Compression strength 10 strain 21000 psi ASTM D 695 Compression strength 1 strain 3500 psi ASTM D 695 480000 psi ASTM D 695 ft-lbsin ASTM D 256 Compression modulus test method Notched impact strength Izod 73 F 0.60 Rockwell hardness M Scale 110 ASTM D 785 Rockwell hardness R Scale 126 ASTM D 785 Thermal properties condition value Vicat softening point comment test method comment 426 F ASTM D 1525 1 Deflection temperature 264 psi 394 F ASTM D 648 2 Deflection temperature 66 psi 410 F ASTM D 648 3 Service temperature short term 392 F - 4 Service temperature Long Term 338 F - 5 Thermal expansion CLTE 3.110 -5 ininF ASTM E 831 6 Thermal conductivity 1.5 BTU-inhr-ft2 -F ASTM D 2214 7 Electrical properties condition value volume resistance 116 1.0 x 10 17 cm ASTM D 257 1 Dielectric strength In Oil 709 Vmil ASTM D 149 2 Dielectric strength In Air 830 Vmil ASTM D 149 3 Dissipation factor 1 kHz 50 RH 73 F 0.0013 ASTM D 150 4 Dielectric constant 1 kHz 50 RH 3.15 ASTM D 150 5 Other properties condition value test method Moisture absorption 24 hrs 73 F .25 ASTM D 570 1 Moisture absorption sat
uration 73 F 1.25 ASTM D 570 2 V0 - 3 pass FAR 25.853 4 Flammability UL94 Flammability 3 mm test method 1 Injection molded data 2 Injection molded data 3 Injection molded data 4 Data obtained from public source 5 Data obtained from public source 6 Injection molded data 7 Injection molded data comment 1 injection molded data 2 injection molded data 3 injection molded data 4 injection molded data 5 Injection molded data comment 1 injection molded data 2 Injection molded data 3 Injection molded data 0.75 mm thickness 4 3.0 mm specimen Resin specification ASTM D 5205-10 PEI0113 Shapes specification ASTM D7293-06 S-PEI0111 This information reflects the current state of our knowledge and is intended only to assist and advise. It is given without obligation or liability. It does not assure or guarantee chemical resistance quality of products or their suitability in any legally binding way. Values are not minimum or maximum values but guidelines that can be used for comparative purposes in material selection. They are within the normal range of product properties and do not represent guaranteed property values. Testing under individual application circumstances is always recommended. Data is obtained from extruded shapes material unless otherwise noted. References to FDA compliance refer to the resins from which the products were made unless otherwise noted. All trade and patent rights should be observed. All rights reserved. Data sheet values are subject to periodic review the most recent update can be found at www.ensingerplastics.com. Ensinger Inc. Headquarters 365 Meadowlands Boulevard Washington PA 15301 USA Phone 800-243-3221 Sales Phone 800-869-4029 Technical Fax 724-746-9209 salesensingerusa.com Date 20180226 Version A1
