SEKISUI SPI Kydex® 6200

Technical Data Sheet KYDEX 6200 Fire-rated sheet for mass transit Introduction KYDEX 6200 is a proprietary high performance thermoplastic sheet designed for use in mass transit vehicles such as subways vans buses and trains. General Information KYDEX 6200 meets both Federal Transit Administration FTA and the Federal Rail Administration FRA requirements for smoke emission and flammability as tested under ASTM E-662 and ASTM E-162. It is the ideal thermoplastic to solve your mass transportation equipment needs. Suggested Applications Seatbacks Bulkhead Components Window Reveals Ceiling Components Features Available in over 200 developed colours various textures and thicknesses from 0.71mm 0.028 and up Easy to clean graffitispray paint lipstick pen grease and grime with cleaners such as Soft Scrub Fantastic and citrus-based cleaners such as Cirti Kleen HD avoid ammoniated cleaners Resistant to a wide range of concentrated chemicals and solvents withstands frequent cleaning without staining or fading Forms to deep draws with low forces when heated to the upper range of 163 - 200C 325 - 392F and an unusually high resistance to hot tearing Can be formed on all standard presses and cut on all standard die-cutting machines Environmental and Safety Considerations SEKISUI SPI is committed to ensuring that its products can be manufactured transported stored used disposed and recycled with an appropriate regard for safety health and environmental protection. We support the safe handling of our products. Please contact our Technical Service department at 800.682.8758 for resources or visit our website httpwww.sekisui-spi.com. For Material Safety Data Sheets please call 800.325.3133. SEKISUI SPI ISO 9001 and 14001 Certified Customer Service 6685 Low St Bloomsburg PA 17815 USA Phone 800.325.3133 1.570.389.5810 Outside the US 1.570.389.5814 Fax 800.452.0155 1.570.387.7786 Email infosekisui-spi.com Technical Service Phone 800.682.8758 Fax 1.570.387.8722 Outside the US 1.57

0.387.6997 techservicesekisui-spi.com Because we cannot anticipate or control the many different conditions under which this information and our products may be used we do not guarantee the applicability of the accuracy of this information or the suitability of our products in any given situation. Users should conduct their own tests to determine the suitability of each product for their particular purposes. Data in the physical property table represents typical values and are to serve only as a guide for engineering design. Results are obtained from specimens under ideal laboratory conditions. Right to change physical properties as a result of technical progress is reserved. THE PRODUCTS DISCUSSED ARE SOLD WITHOUT WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE EITHER EXPRESSED OR IMPLIED EXCEPT AS PROVIDED IN OUR STANDARD TERMS AND CONDITIONS OF SALE. Buyer assumes all responsibility for loss or damage arising from the handling and use of our products whether done in accordance with directions or not. In no event shall the supplier or the manufacturer be liable for incidental or consequential damages. Also statements concerning the possible use of our products are not intended as recommendations to use our products in the infringement of any patent. Consult local code and regulatory agencies for specific requirements regarding code compliance transporting processing recycling and disposal of our product. Product not intended for use as a heat resistant surface. Texture product grade and other conditions may cause variations in appearance. sekisui-spi.com This information supersedes all previously published data. 2014 Sekisui Polymer Innovations LLC. All rights reserved. KYDEX is a registered trademark of Sekisui Polymer Innovations LLC. 091614 Technical Data Sheet KYDEX 6200 Fire-rated sheet for mass transit Physical Properties Property Test Method Typical Value1 Specific Gravity ASTM D-792 1.40 Tensile Strength ASTM D-638 41 MPa 6000 psi Flexural S

trength ASTM D-790 63 MPa 9200 psi Modulus of Elasticity ASTM D-790 2413 MPa 350000 psi Notched Izod Impact Resistance 23C 73F ASTM D-256 187 Jm 3.5 ft-lbsin Coefficient of Linear Thermal Expansion ASTM D-696 7.92 x 10-5 C 4.4 x 10-5 F Rockwell Hardness R Scale ASTM D-785 Taber Abrasion Resistance Wt. Loss 1000 cycles ASTM D-1044 0.042g Heat Deflection Temperature HDT 1.8 MPa 264 psi annealed ASTM D-648 77.8C Flammability2 Independent Laboratory Testing UL Standard 94 V-0 Flammability Vertical Burn 60-second Vertical Burn 12-second FAR 25.853 ai FAR 25.853 aii PASS PASS Flammability Motor Vehicle Safety Standard FMVSS 302 Pass Flammability Radiant Panel Is ASTM E-162 35 Flammability Smoke Generation ASTM E-662 100 1.5min 200 4.0 min Flammability Fire Behavior Classification DIN 5510-2 0.9mm S4 ST2 SR2 6.80mm S4 ST2 SR2 98 172F 1 Values based upon 3.18mm 0.125 sheet unless otherwise specified. 2 All thicknesses 0.71mm 0.028 and above Not intended for specification purposes. SEKISUI SPI ISO 9001 and 14001 Certified Customer Service 6685 Low St Bloomsburg PA 17815 USA Phone 800.325.3133 1.570.389.5810 Outside the US 1.570.389.5814 Fax 800.452.0155 1.570.387.7786 Email infosekisui-spi.com Technical Service Phone 800.682.8758 Fax 1.570.387.8722 Outside the US 1.570.387.6997 techservicesekisui-spi.com Because we cannot anticipate or control the many different conditions under which this information and our products may be used we do not guarantee the applicability of the accuracy of this information or the suitability of our products in any given situation. Users should conduct their own tests to determine the suitability of each product for their particular purposes. Data in the physical property table represents typical values and are to serve only as a guide for engineering design. Results are obtained from specimens under ideal laboratory conditions. Right to change physical properties as a result of technical progress is reserved. THE PRODUCTS DISCUSSED ARE SO

LD WITHOUT WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE EITHER EXPRESSED OR IMPLIED EXCEPT AS PROVIDED IN OUR STANDARD TERMS AND CONDITIONS OF SALE. Buyer assumes all responsibility for loss or damage arising from the handling and use of our products whether done in accordance with directions or not. In no event shall the supplier or the manufacturer be liable for incidental or consequential damages. Also statements concerning the possible use of our products are not intended as recommendations to use our products in the infringement of any patent. Consult local code and regulatory agencies for specific requirements regarding code compliance transporting processing recycling and disposal of our product. Product not intended for use as a heat resistant surface. Texture product grade and other conditions may cause variations in appearance. sekisui-spi.com This information supersedes all previously published data. 2014 Sekisui Polymer Innovations LLC. All rights reserved. KYDEX is a registered trademark of Sekisui Polymer Innovations LLC. 091614