Saint-Gobain TYGON® E-1000

Tygon E-1000 Pumpable Tubing for Food Beverage Dispensing Soft and flexible Tygon E-l000 tubing delivers superior performance in a formulation that contains non-DEHP Bis 2-ethylhexyl phthalate plasticizers. Tygon E-l000 non-DEHP tubing has been tested rigorously to meet stringent standards for low temperature and corrosive chemical resistance. Ideal Selection for Complex Set-Ups Tygon E-l000 tubing is an excellent solution to applications requiring complicated set-ups with sharp radius curves and multiple directional changes. Tygon E-l000 tubing resists twisting and collapse which are common problems when using other tubing products. Tygon E-l000 tubing stays flexible at temperatures as low as -67F -55C. The Preferred Tubing in Low-Torque Peristaltic Pumps The extremely low durometer 40 of Tygon E-1000 tubing provides minimal resistance to compression. This feature is ideal when using low-torque or battery-driven peristaltic pumps. Tygon E-1000 tubing provides an excellent alternative to silicone tubing where corrosive chemicals are used. Tygon E-l000 tubing will typically outlast silicone tubing in peristaltic pump applications by a margin of 2 to 1. Features and Benefits Soft and flexible Low-temperature resistant -67F -55C Resistant to corrosive chemicals Low durometer for use in low-torque pump applications Meets FDA 21 CFR 175.300 requirements for food contact Typical Applications Peristaltic pumps Vent and drain lines Tygon E-1000 www.processsystems.saint-gobain.com Tygon E-1000 Part Number ID Wall Thickness OD in mm in Min. Bend Radius mm in mm in mm Max. Working Pressure 73F 23C psi bar Vacuum Rating 73F 23C inHg mmHg ADK00003 116 1.59 316 4.76 116 1.59 18 3.18 26 1.8 29.9 760 ADK00007 18 3.18 14 6.35 116 1.59 38 9.53 16 1.1 29.9 760 ADK00012 316 4.76 516 7.94 116 1.59 58 15.88 10 0.7 15.0 381 ADK00017 14 6.35 38 9.53 116 1.59 1 25.40 8 0.6 7.0 178 ADK00019 14 6.35 12 12.70 18 3.18 58 15.88 14 0.9 29.9 760 127 ADK00022 516 7.94 716 11.11 1

16 1.59 1-38 34.93 7 0.5 5.0 ADK00027 38 9.53 12 12.70 116 1.59 1-34 44.45 7 0.5 3.0 76 ADK00029 38 9.53 58 15.88 18 3.18 1-18 28.58 11 0.8 15.0 381 ADK00036 12 12.70 58 15.88 116 1.59 2-78 73.03 6 0.4 2.0 51 ADK00038 12 12.70 34 19.05 18 3.18 1-34 44.45 8 0.6 7.0 178 Working pressures are calculated at a 15 ratio relative to burst pressure using ASTM D1599. Additional sizes available upon request. Relative Chemical Resistance Properties Acids Bases Conc. Med. Weak Conc. Med. Weak F E E E E E Salts Alcohols Ketones E F U E Excellent F Fair U Unsatisfactory All tests conducted at room temperature. Regulatory Compliance Typical Physical Properties Property ASTM Method Value or Rating Durometer Hardness Shore A 15 sec D2240 40 Clear Color Opacity Translucent Tensile Strength psi MPa D412 1100 7.6 Ultimate Elongation D412 435 Tear Resistance lb-fin kNm D1004 104 18.2 Specific Gravity D792 1.10 Water Absorption at 73F 23C for 24 hrs. D570 0.29 Compression Set Constant Deflection at 158F 70C for 22 hrs. D395 55 Maximum Recommended Operating Temp. F C 125 52 Brittleness by Impact Temp. F C D746 -67 -55 Tensile Stress psi MPa 100 Elongation D412 286 2.0 FDA Approved for Food Contact Yes Contains REACH SVHC No NSF 51 Standard Pending Sterilization Methods Gas USP Class VI No The values listed for working and burst pressures are derived from tests conducted under controlled laboratory conditions. Many factors will reduce the tubings ability to withstand pressures including temperature chemical attack stress pulsation and the attachment to fittings. It is imperative that the user conduct tests simulating the conditions of the application prior to specifying the tubing for use. TYGON E-1000 TUBING IS NOT INTENDED FOR USE AS AN IMPLANT MATERIAL. Unless otherwise noted all tests were conducted at room temperature 73F. Values shown were determined on 0.075 thick extruded strip or 0.075 thick molded ASTM plaques or molded ASTM durometer buttons. NOTE The data and detai

ls given in this document are correct and up to date. This document is intended to provide information about the product and possible applications. This document is not the product specification and does not provide specific features nor does it guarantee product performance in specific applications. Saint-Gobain cannot anticipate or control the conditions of the field and for this reason strongly recommends that practical tests are conducted to ensure that the product meets the requirements of a specific application. Tygon is a registered trademark. FLS-6114-0416-SGPS 2016 Saint-Gobain Performance Plastics