JT828P www.Mactac.com Version 11 0217 Approved by J. S. Product IMAGin Printvinyl JT828P Product Description JT828P is a 3.9-mil matte white soft-calendared PVC film designed for UV and solvent-based ink jet printing. The product is coated on one side with a clear permanent acrylic pressure sensitive adhesive and supplied with a 74 Kraft liner. JT828P is designed for general purpose indoor and short term outdoor advertising and promotion on flat or slightly curved surfaces. Physical Properties Property Peel Adhesion lb.in. N25mm 180 on glass - 24 hr. Quick Tack lb.in N25mm Stainless Steel Typical Values Test Method FTM - 1 3.2 - 4.5 14 - 20 FTM - 9 2.1 - 3.2 9 - 14 Dimensional Stability 48 hours 158F max 1.0 Temperature Ranges Minimum Application End Use 40F 5C -5F to 158F -20C to 70C FTM - 14 10 x 10 Sample Bonded to aluminum Durability The indoor durability of this film is 5 - 6 years and the outdoor durability of the unprinted film is up to 4 years. Over lamination of the inkjet-printed material with Permacolor overlaminates minimizes yellowing of the print media and delays color fading that may occur over time. This color fading is mainly dependent upon the inks quality see technical data sheets given by the ink manufacturers and the pressure sensitive media being used. Shelf Life 2 years from D.O.M. when stored at 6077F 1525C and 50 relative humidity in the original package. Approved Printing Processes Screen Printing UV Cured Solvent Digital UV Inkjet Eco-solvent True solvent Latex HP Indigo Off-set Off-set UV Thermal Transfer Flexographic Laser Jetrion To achieve the best possible print quality please make sure that the correct ICC profiles or printer settings are used. Profiles can be obtained from our Distributors or can be downloaded from www.mactac.com . Printer and heater settings and ICC profiles can also be downloaded from some O.E.M. or software manufacturers websites. The ICC profiles are provided solely as a customer 3 If this is a printed Perf
ormance Guide it is an uncontrolled document. Please check the Mactac website for the latest most up-to-date version Recommendations Always test your combination of IMAGin M Series products inks and laminating films prior to commercial use. 1. Printing Conditions Print in conditioned pressroom at 73F 23C and 50 RH. The maximum allowable ink saturation is 270. 2. Drying Requirements Solvent Eco-solvent and Mild-solvent inkjet prints require 24 - 48 hr. drying time - open to the air. Inks do not dry when printed media is rolled up. The prints must be dry prior to lamination. 3. Laminating Conditions If the printed graphic is likely to be exposed to corrosive liquids smoke fumes and highly polluted areas or there is a likelihood of scratching it is highly recommended to laminate with Permacolor ColorGard LUV series intermediate or PromoGard economy overlaminating films. Please be aware that adding an overlaminate will significantly reduce conformability to complex surfaces. 4. Transportation Conditions To allow for easy transportation IMAGin M Series can be rolled up with the image out with a minimum diameter of 6 inches 15cm. When the image is not protected by an overlaminate make sure the print is completely dry and protected in a plastic bag. During transportation or storage avoid exposing them to extreme temperature and humidity changes. Values given are typical and are not necessarily for use in specification. IMPORTANT NOTICE The information given and the recommendations made herein are based on our research and are believed to be accurate but no guarantee of their accuracy or completeness is made. In every case user shall determine before using any product in full scale production or in any way whether such product is suitable for users intended use for their particular purpose under their own operating conditions. User assumes all risk and liability whatsoever in connection with their use of any product. The products discussed herein are sold without any warra
nty as to merchantability or fitness for a particular purpose or any other warranty express or implied. No representative of ours has any authority to waive or change the foregoing provisions and no statement or recommendation not contained herein shall have any force of effect unless in an agreement signed by the officers of seller and manufacturer. Nothing contained herein shall be construed to imply the nonexistence of any relevant patents or to constitute a permission inducement or recommendation to practice any invention covered by any patent without authority from the owner of the patent. The following is made in lieu of all warranties express or implied Sellers and manufacturers only obligation shall be to replace or credit such quantity of the product proved to be defective at its discretion. TM Trademark of Morgan Adhesives Company LLC Registered Trademark of Morgan Adhesives Company LLC www.Mactac.com
