Mactac® IMAGin® JDT429 Digitrans
JDT429 www.Mactac.com Version 12 0416 Approved by J. S. Product IMAGin JDT429 Digitrans Product Description JDT429 Digitrans is a 4-mil soft white gloss calendered PVC film designed for solvent-based ink jet printing. The product is coated on one side with a semi-permanent black opaque acrylic pressure sensitive adhesive and supplied with a 74 Kraft liner. JDT429 is designed for short-term outdoor mobile advertising on flat to slightly curved surfaces. Typical Uses Busses Taxis Physical Properties Property Peel Adhesion lbin. N25mm 180 on glass - 20 min. - 24 hr. Quick Tack lbin N25mm Stainless Steel Subway trains Wall murals Typical Values FTM - 1 0.95 - 1.8 4 - 8 2.1 - 3.0 9 - 13 FTM - 9 0.95 - 1.8 4 - 8 Dimensional Stability 48 hours 158F max 0.2 Temperature Ranges Minimum Application End Use 46F 8C -4F to 158F -20C to 70C Flammability Surface Burning Characteristics Flame Spread Smoke Density ANSI NFPA and IFC Test Method Self-extinguishing 5 35 Class A FTM - 14 10 x 10 Sample Bonded to aluminum ISO 3795 ASTM E84-01 or ANSINFPA 255 or IFC 8-1 APPROVED BY Out Front Media and Clear Channel For Bus Posters including King-size Super King-size Queen-size Bus Poster with extensions and snipes Headlight Displays Taillight Displays Headliners and Michelangelo. Durability The outdoor durability of the unprinted film is 3 years. JDT429 has up to 2 year removability after application. Removal after the first year may result in some slight adhesive residue which can be easily cleaned off with alcohol or adhesive remover. Shelf Life 2 year from D.O.M. when stored at 6077F 1525C and 50 relative humidity in the original package. Removability This product has 1 year clean and easy removability after application on many surfaces. The removability of JDT429 may be affected by the following substrates polystyrene nitrocellulose painted surfaces and soft PVC. With such substrates an increase of adhesion over time may occur and adhesive residue on removal may be noticed. Appr
oved Print Materials Screen Printing HP Indigo UV Cured Off-set Solvent Off-set UV Digital UV Inkjet Thermal Transfer Eco-solvent Flexographic True solvent Laser Latex Jetrion To achieve the best possible print quality please make sure that the correct ICC profiles or printer settings are used. Profiles can be obtained from our Distributors or can be downloaded from www.mactac.com . Printer and heater settings and ICC profiles can also be downloaded from some O.E.M. or software manufacturers websites. The ICC profiles are provided solely as a customer resource. Print environments the individual nature of printing systems inks and software can significantly affect output. It is the customers responsibility to determine the suitability of any profile for use in their specific print environment. Limitations Due to the wide variability of interior walls sealants and paints no claims for successful applications to or removal from painted wall surfaces are made by Mactac. It is the users responsibility to determine the products suitability for the intended wall. 1 The user is responsible for determining the products suitability including adhesion and if needed removal characteristics when used in applications other than listed specifically in this Performance Guide. 2 If there are any questions about applications please contact your Mactac sales representative to discuss your requirements for recommendations. 3 If this is a printed Performance Guide it is an uncontrolled document. Please check the Mactac website for the latest most up-to-date version. Recommendations Always test your combination of JT5000 products inks and laminating films prior to commercial use. 1 Printing Conditions Print in conditioned pressroom at 73F 23C and 50 RH. Ink saturation should not exceed 270. 2 Drying Requirements Solvent Eco-solvent and Mild-solvent inkjet prints require 24 - 48 hr. drying time - open to the air. Inks do not dry when printed media is rolled up. The prints must be dry pr
ior to lamination. 3 Laminating Conditions If the printed graphic is likely to be exposed to corrosive liquids smoke fumes and highly polluted areas or there is a likelihood of scratching it is highly recommended you laminate with Permacolor ColorGard LUV series intermediate or PromoGard PG7000 Gloss economical overlaminating films. Please be aware that adding an overlaminate will significantly reduce conformability to complex surfaces. 4 Transportation Conditions To allow for easy transportation IMAGin JT5000 series can be rolled up with the image out with a minimum diameter of 6 inches 15cm. When the image is not protected by an overlaminate make sure the print is completely dry and protected in a plastic bag. During transportation or storage avoid exposing them to extreme temperature and humidity changes. Values given are typical and are not necessarily for use in specification. IMPORTANT NOTICE The information given and the recommendations made herein are based on our research and are believed to be accurate but no guarantee of their accuracy or completeness is made. In every case user shall determine before using any product in full scale production or in any way whether such product is suitable for users intended use for their particular purpose under their own operating conditions. User assumes all risk and liability whatsoever in connection with their use of any product. The products discussed herein are sold without any warranty as to merchantability or fitness for a particular purpose or any other warranty express or implied. No representative of ours has any authority to waive or change the foregoing provisions and no statement or recommendation not contained herein shall have any force of effect unless in an agreement signed by the officers of seller and manufacturer. Nothing contained herein shall be construed to imply the nonexistence of any relevant patents or to constitute a permission inducement or recommendation to practice any invention covered b
y any patent without authority from the owner of the patent. The following is made in lieu of all warranties express or implied Sellers and manufacturers only obligation shall be to replace or credit such quantity of the product proved to be defective at its discretion. TM Trademark of Morgan Adhesives Company LLC Registered Trademark of Morgan Adhesives Company LLC www.Mactac.com