Delrin 150 black (TECAFORM AD)
DELRIN 150 Series Natural TECAFORM AD - Stock Shapes rods plates tubes Chemical Designation POM-H Polyacetal Homopolymer Colour white Density 1.41 gcm3 Main features good machinability high stiffness high fatigue strength high creep resistance good wear properties very good abrasion resistance Target Industries food processing food engineering automotive industry conveyor technology construction industry mechanical engineering electronics fixture construction gear manufacturing home appliances Mechanical properties condition value Modulus of elasticity tensile test 73 F 350000 psi test method ASTM D 638 11000 psi ASTM D 638 Elongation at break tensile test 73 F 25 ASTM D 638 Flexural strength 73 F 14000 psi ASTM D 790 Modulus of elasticity flexural test 73 F 470000 psi ASTM D 790 Compression strength 1 strain 3600 psi ASTM D 695 Compression strength 10 strain 15500 psi ASTM D 695 325000 psi ASTM D 695 ft-lbsin - Tensile strength at yield Compression modulus Impact strength Izod 73 F 1.5 Rockwell hardness 73 F M Scale R Scale 94 120 ASTM D 785 Shore hardness D scale 84 ASTM D 2240 Coefficient of friction Dynamic 40 psi 50 fpm .2 ASTM D 3702 Wear rate 40 psi 50 fpm 5510-10 Thermal properties condition value Melting temperature in-minft-lbs-hr ASTM D 3702 test method 347 F ASTM D 2133 Deflection temperature 66 psi 336 F ASTM D 648 Deflection temperature 264 psi 257 F ASTM D 648 Service temperature Intermittent 300 F - Service temperature Long Term 185 F - Thermal expansion CLTE 6.810 -5 ininF ASTM D 696 Specific heat 0.35 BTUlb-F - Electrical properties condition value volume resistance Dielectric strength comment comment 1 test method 10 15 cm ASTM D257 500 Vmil ASTM D 149 1 Injection molded sample comment Dissipation factor 60 Hz 73 F .005 Dielectric constant 60 Hz 73 F 50 RH 3.7 ASTM D 150 ASTM D 150 Other properties condition value test method comment Moisture absorption 24 hrs 73 F .25 ASTM D 570 1 1.47mm injection mold Moisture absorption saturati
on 73 F .90 ASTM D 570 Flammability UL94 UL 94 HB - 1 Resin specification ASTM D6778-06 POM0111 superseding ASTM D4181-00 POM111 Shapes specification ASTM D6100-11 S-POM0111 This information reflects the current state of our knowledge and is intended only to assist and advise. It is given without obligation or liability. It does not assure or guarantee chemical resistance quality of products or their suitability in any legally binding way. Values are not minimum or maximum values but guidelines that can be used for comparative purposes in material selection. They are within the normal range of product properties and do not represent guaranteed property values. Testing under individual application circumstances is always recommended. Data is obtained from extruded shapes material unless otherwise noted. References to FDA compliance refer to the resins from which the products were made unless otherwise noted. All trade and patent rights should be observed. All rights reserved. Data sheet values are subject to periodic review the most recent update can be found at www.ensingerplastics.com. Ensinger Inc. Headquarters 365 Meadowlands Boulevard Washington PA 15301 USA Phone 800-243-3221 Sales Phone 800-869-4029 Technical Fax 724-746-9209 salesensingerusa.com Date 20220329 Version A4